Inquiry
Form loading...

NDA and Mold Ownership: How to Protect a Custom Glass Bottle Design When Sourcing From China

2026-10-22
Custom 100ml square mist perfume bottle with spray pump and glass cap
Custom square mist perfume bottle with spray pump and glass cap, item JYGB-0014, in the capacity and dimension range covered by this article's mold ownership framework.

Most bottle quotes arrive with a price, a lead time and a minimum order quantity. Almost none of them arrive with a clause about who owns the mold. That omission is not unusual, and it is not automatically bad faith. It is simply an unasked question, and in a custom Glass Bottle project the unasked question is the one that decides whether the brand ends up with a distinctive product or with a shape that three competitors are already filling.

This article is written for the brand owner, the product manager and the packaging buyer who has decided that the bottle has to be theirs rather than merely their order. It covers four asset classes, the anatomy of a mutual non-disclosure agreement, the five sentences that decide whether a mold transfer clause actually works, the four questions that expose a supplier's real position, and what happens when a custom mold is the wrong route altogether.

A custom glass bottle project carries four different kinds of asset, and the single word most buyers use to cover them, mold ownership, does not distinguish between them at all. Separating those four assets is the first step of protecting the design.

One point of disclosure before going further. This article does not state that any particular supplier offers a standard mutual NDA or transfers mold ownership on request. Nothing of the kind appears anywhere in the published record of Jingyan Trading at the time of writing, and an article that implied otherwise would be worse than no article at all. What follows is a verification framework a buyer can apply to any supplier, applied in detail to real, published specifications from one named supplier.

Four asset classes, four different claims

The phrase mold ownership collapses four legally and commercially distinct assets into one word, and most disputes happen because the parties never separated them. A bottle project produces at least these four things.

The mold or die itself. The physical steel or alloy tooling. For glass this is a multi-cavity mold with cavity plates and inserts, plus the machine-specific holder assembly. This is the asset with real resale and reuse value, and it is the asset a factory is most likely to defend, because a die can be re-run indefinitely for another customer at almost no marginal engineering cost.

The design file. The 2D drawings, the 3D model, the cross-section, the neck and thread specification, and the tolerances. These are a derivative work of the buyer's industrial design, but they are also the file a factory needs to make the part. This is where the leak risk is highest, because a 3D file is trivially forwarded and impossible to recall.

The decoration assets. Logos, wordmarks, artwork separations, screen-print film, decal artwork, electroplate masks and frosting screens. These are unambiguously the buyer's intellectual property from the moment the buyer supplies them, and they are the assets most often used without permission once they leave the factory.

The compound and fill specification, where the project is a filled product rather than an empty component. A fragrance or cosmetic formula supplied by the brand is trade-secret material under most regimes, and its treatment needs its own clause, separate from the packaging clause.

Each asset needs its own sentence in the contract. A single sentence covering all four is either too vague to enforce or so broad that a reasonable supplier will refuse to sign it.

Anatomy of a non-disclosure agreement worth signing

A mutual NDA is a short document. The version most brand owners receive from a factory is a one-sided promise by the factory to keep the buyer's drawings secret, and it is usually drafted so narrowly that it protects nothing that matters. A workable agreement needs the following elements, in roughly this order.

Definition of confidential information that names the specific categories rather than the generic phrase all business information, and that explicitly includes drawings, 3D files, mold quotations, tooling schedules, projected volumes, artwork, and the existence of the project itself.

The permitted purpose clause, which narrows use to evaluating, quoting and producing the specific named SKU. Without a purpose clause, a confidentiality promise is unenforceable in practice because there is no defined breach.

The residuals carve-out, stating that information the receiving party can demonstrate was already lawfully known, was independently developed without reference to the disclosed material, or is lawfully available from a third party, falls outside the agreement. A supplier who cannot accept a fair residuals clause is telling you something.

The term, which should run at least as long as the life of the information. A two-year confidentiality term on a design that will be on a shelf for five years is a term that expires before the risk does.

Return and destruction on request, with a carve-out for the single archival copy the receiving party is required to retain for legal or insurance purposes.

Governing law, dispute forum and, ideally, an arbitration clause with a named seat. Cross-border enforcement of a confidentiality promise is slow and expensive, which is precisely why the forum clause matters more than the boilerplate.

The signature test is simple. A mutual agreement binds both parties. An agreement that binds only the buyer to keep its own design confidential while the supplier reserves the right to use that design is not a non-disclosure agreement, it is a permission slip.

The transfer clause: five sentences that decide the outcome

Assuming both sides agree that the buyer should end up with the tooling, the wording is still where most transfers quietly fail. Five elements have to be present, and each of them has a failure mode.

The trigger. Title must pass on a defined event, not on a vague intention. The event is usually the buyer paying the tooling charge in full, or the completion of the first approved article and a written release. A clause that says ownership transfers on agreement is unenforceable because agreement is not a fact that can be evidenced.

The inventory. The clause must enumerate what physically transfers: the mold body, cavity plates, inserts, and any holder or adaptor specific to that bottle. If the mold only works in one particular machine and the holder stays with the factory, the buyer has received a tool that cannot be run, which is not ownership in any useful sense.

The moment of passage. Title passes automatically and without further paperwork once the trigger occurs. A clause requiring a separate transfer document creates a second event that can be forgotten, delayed or disputed at the worst possible moment.

The evidence. The clause should require the supplier to mark the tool physically, for example engraving the buyer's item code into the cavity plate or the mold body, and to provide dated photographs of the marked tool as part of the handover. An unmarked tool sitting in a factory rack among four hundred others is a tool you will have difficulty proving you own.

The end-of-life obligation. What happens to the tool when the buyer stops ordering. This is where most disputes actually live. Without a clause, the tool sits in the supplier's rack indefinitely, and a supplier under financial pressure has every incentive to treat it as available inventory. A buyer's clause typically requires storage for a defined number of years, requires written notice and a shipping window before any disposal, and requires destruction if the buyer does not collect.

The exclusive-use question is separate from all five. A buyer who wants to prevent the supplier from running the identical geometry for a competitor has to ask for that explicitly. It is a stronger request than mold ownership, it is often refused, and it should be evaluated as a commercial decision rather than assumed.

Four questions that reveal the supplier's real position

Before signing anything, ask four questions and require the answers in writing on the purchase order or in the contract schedule rather than in a chat message. A chat answer is convenient for the supplier and worthless for the buyer.

Who holds title in the shapes already in your catalogue? A supplier that answers this clearly and points to an existing policy is a supplier that has had this conversation before. A supplier that answers vaguely has probably never had it.

Will you engrave our item code into the tool? A supplier who declines to mark the tooling has a reason, and the reason is usually that they intend to keep running it. Physical marking is cheap and it is the single most effective deterrent against unapproved reuse.

Will you release the production drawing before the tooling release approval? The drawing is the buyer's design expressed in manufacturing form. If the supplier keeps it, the buyer has paid for a bottle and handed over the ability to copy it.

What happens to the tool if we stop ordering? The answer reveals whether the supplier is planning for a relationship or for an order. A supplier that will commit to storage terms and a disposal process has accepted the existence of a continuing obligation after the last purchase order, which is exactly what ownership requires.

What the published record covers, and where it stops

Applying the framework honestly requires stating exactly what the supplier's own published material does and does not contain.

The public record of this supplier is substantial on manufacturing and entirely silent on intellectual property. The company profile and the about page describe Jingyan Tradingas a one-stop shop for REED DIFFUSER accessories and cosmetic packaging, state that the company operates two factories in Jinhua and Huzhou in Zhejiang Province with a total area of 28,000 square metres, state ISO9001-2015 certification, and state a catalogue of more than 1000 items. The same pages describe a five-stage quality process covering raw material, equipment, finished product and final inspection, a raw material sourcing policy built on partners of more than ten years, a business team with seven to eight years in the industry, and a stated policy of reinvesting between 20% and 30% of total profit into research and development each year.

The our quality philosophy page sets out four commitments, to employees, customers, suppliers and shareholders. It is a genuine statement of operating intent and it is worth reading before a first order. It is also, precisely, a statement about people, service, supply relationships and returns. It contains no clause on confidentiality, no clause on ownership, and no mention of tooling. Reading it and hoping to find a mold transfer policy in it is a category error.

The aromatherapy bottle catalog is where the same distinction becomes unavoidable, and the section that follows applies all four asset classes to one specific published item.

The customer service page lists pre-sale and trade-capacity commitments that a documentation-minded buyer will care about: twenty-four hour online sales coverage, free samples, assistance with market analysis, provision of customer documents including MSDS, insurance and country of origin, transmission of estimated time of departure and arrival, and a formal eight-step procedure for handling product claims. That is a real trade-compliance posture. It is not an intellectual property posture, and it should not be read as one.

So the honest summary is this. The verifiable substrate exists, and it is verifiable: the factories, the certification, the catalogue depth, the inspection stages, the documented claim procedure. The intellectual property layer has to be created per project, by negotiation, and it will not be found in a brochure. A buyer who asks for it will be answered; a buyer who assumes it has been handled is the one who ends up with a shape on a competitor's shelf.

Running the check on one real specification

The framework is easier to use against a concrete item. Consider a specific square mist bottle from this supplier's published range, listed in the 50/100ml square mist perfume bottle page under item number JYGB-0014. Its published parameters are as follows.

The bottle is offered in 50ml and 100ml capacities. The 50ml measures 50mm diameter by 81mm height, and the 100ml measures 63mm diameter by 94mm height. Colour is transparent, with customisation available. Closure is a spray pump with a glass cap. Customisation is offered on size, bottle type, logo, sticker or label, and packing box, with decoration methods listed as painting, decal, screen printing, frosting, electroplate, embossing, fade and label. The published minimum order quantity is 3000 pieces, which the supplier states can be lower where stock exists, and 10000 pieces for a customised logo. Published delivery is seven to fifteen days after order payment where stock exists, and twenty to thirty-five days where it does not.

Now apply the four asset classes to that specification, because they separate cleanly.

Custom 50ml and 100ml square mist perfume bottle with spray pump and glass cap, JYGB-0014
Custom 50ml and 100ml square mist perfume bottle with spray pump and glass cap, JYGB-0014

The decoration assets are unambiguous buyer property. A logo supplied by the brand, and the screen printing or electroplate separations derived from it, remain the buyer's property throughout. Every screen used to apply that logo is a physical carrier of the buyer's trademark. That is the easiest clause in the entire project and the one most often left implicit.

The geometry is where the real question sits. The square shoulder, the proportion of the 50ml and 100ml bodies, the neck and closure interface, the dimensional tolerances: these determine whether the bottle looks like your brand and only your brand. If the buyer wants to stop the supplier running that exact geometry for another fragrance house, that has to be requested as exclusivity, separately from ownership of the tool.

The tool transfer question is narrower than buyers expect. What actually needs to transfer is the cavity set that produces the square body and the shoulder. The spray pump and the glass cap are separate components with their own supply chains, and the packing box is a separate item entirely.

The documentation already exists as a habit. The published claim that customer documents including MSDS, insurance and country of origin are provided, together with a documented claim-handling procedure, means the factory already operates a document-packet process. The mold transfer certificate belongs inside that same packet. It is an extension of an existing routine, not the invention of a new one, which is the strongest practical argument for raising it early.

The wider aromatherapy bottle catalogmakes the ownership question sharper rather than softer. Its published listings include a round 100ml diffuser bottle at 43mm by 113mm, a round 50ml, 100ml and 150ml Bottle at 55mm by 75mm, a square 150ml bottle at 49.8mm by 127mm, a 200ml diffuser bottle, a 250ml ceramic round bottle, and clear 50ml and 100ml bottles advertised with an engraved logo. Similar shapes at specific dimensions, offered as catalogue items with logo engraving available as an option, mean that the geometry in question is capable of being sold to more than one buyer. That is not an accusation of anything. It is simply the commercial reality of a supplier with a catalogue, and it is the reason a buyer who wants exclusivity has to buy it explicitly.

When a custom mold is the wrong route

The honest version of this advice includes the cases where the buyer should not commission tooling at all. There are three.

When the volume cannot amortise the tool. A custom die is an up-front engineering cost that is recovered across production. The minimum order quantity published for a customised logo on a stock square bottle is 10000 pieces, against 3000 for the unmodified bottle. That gap is a reasonable public signal of where the factory sees the commercial break. A project whose realistic lifetime volume sits below that threshold is better served by a catalogue geometry with strong decoration.

When the differentiation can be carried entirely by decoration. A catalogue bottle with a bespoke screen print, an electroplate finish, a unique colour and a branded closure is frequently indistinguishable on shelf from a custom-mould bottle, and it retains the flexibility of changing geometry in the next product cycle without renegotiating a tooling agreement.

When the risk of a binding tool commitment outweighs the commercial benefit. A transfer clause is an ongoing obligation on the factory. A supplier who refuses to commit to storage and disposal terms is telling the buyer something real about how they intend to operate. At that point, the buyer has two honest options: accept catalogue geometry, or choose a supplier whose operating model supports a transfer clause. Neither is a failure.

A related decision concerns geography and logistics. Tooling that moves between factories is tooling that generates freight, insurance, customs and handling questions of its own, and the trade documentation burden does not end with the bottle order. Buyers who take Incoterms decisions seriously for the goods should take the same seriousness for the tool, and the Incoterms rules published by the International Chamber of Commerce are the standard reference for that conversation.

Documentation that survives a claim

Packaging disputes are rarely about the bottle. They are about paper. The supplier's own published trade-capacity commitments give a buyer a usable skeleton, and a documentation-minded buyer should build the ownership layer on top of exactly that structure.

Documents that already exist in the ordinary packet include the safety data sheet, the insurance certificate, the certificate of origin, the estimated time of departure, the estimated time of arrival, and the shipping and packing specification. A buyer's ownership file should add four items to that packet: the executed non-disclosure agreement, the tooling schedule identifying each cavity and insert by item code, the mold transfer certificate with dated photographs of the marked tool, and the storage and disposal undertaking.

Keeping those four items inside the existing document flow rather than in a separate legal file is the difference between a clause that is honoured and a clause that is forgotten. A clause that lives only in the contract and never appears in the shipping paperwork is a clause that no one on either side will remember when the order has been running for two years.

For buyers who intend to protect the bottle shape as a design asset rather than merely as a purchased part, the formal route also exists and is worth understanding before negotiations start. Design protection is a separate mechanism from trade secret protection and from trademark registration: a design right, whether registered in one territory or under an international system, addresses what an unauthorised party may do with the appearance itself, whereas an NDA addresses only what a party has been told in confidence. The World Intellectual Property Organization publishes plain-language overviews of both, at its design and industrial property pages and its copyright pages, and national authorities such as the United States Patent and Trademark Office publish comparable material for patent and trade mark filings.

None of that replaces the NDA. A registered right does not stop a factory from quietly producing your geometry for someone else; an NDA does not stop a competitor who never saw your drawings. The two mechanisms answer different questions, and a serious custom bottle project usually needs both.

FAQ

Q1: Do Chinese bottle factories sign mutual NDAs, or is it unusual?

Mutual NDAs are entirely ordinary in custom packaging work and are routinely signed at the specification stage, before any drawing is exchanged. What varies between suppliers is not willingness but drafting quality. Many factories will happily sign a narrow one-sided promise that protects only the buyer, which reads like an NDA but does not protect the buyer's design from being reused. Ask for a mutual document and check that the factory is bound by the same confidentiality obligation as you are.

Q2: If a factory manufactures my design, does that mean they own it?

Ownership is determined by contract and by applicable design and copyright law, not by whoever presses the physical object. In the absence of a written agreement, the position is genuinely uncertain and the outcome is rarely decided in the buyer's favour. That uncertainty is the reason the clause has to be written before tooling starts rather than negotiated after the first shipment.

Q3: How much does a custom glass bottle mold cost and how long does it take?

Suppliers generally price tooling as a separate line item from the unit price, and the figures depend on cavity count, machine specification and geometry complexity, so they are quoted per project rather than published. Lead time for the tool is also separate from production lead time. Ask for the tooling quotation and the tooling schedule as named deliverables in the quotation, together with the drawing approval milestone that precedes cutting.

Q4: Can a supplier refuse to transfer mold ownership?

Yes, and some will, particularly where the catalogue shape has other customers or where the factory values the ability to re-run the tool. It is a legitimate commercial position rather than misconduct. The useful question is not whether they will transfer it but whether they will commit to physical marking, storage and disposal obligations, which protects the buyer's interest even where ownership itself is contested.

Q5: What is the difference between exclusivity and mold ownership?

Ownership determines who controls the tool. Exclusivity determines whether anyone else may run the same geometry for a competitor. A supplier can agree to transfer the mold and still sell that shape to another brand, so the two clauses have to be written separately. Exclusivity is a stronger request, is often declined, and should be evaluated as a commercial decision.

Jingyan Trading Editorial Team